Skip to content

Setup guide

NerdOctaxe Setup Guide: Power, Wi-Fi, Pool, Tuning and the Hydro

Eight BM1370 chips on one board, around 14 TH/s and 220 W: the NerdOctaxe is set up like every miner of its family, but power, heat and tuning deserve more care. This guide covers the Rev 3.1 and the Hydro from the power supply to the first shares, then frequency, cooling, updates and every error message the display can show.

Written and tested by the Nerdminer Store team. Updated on 16 November 2026

Don't have a NerdOctaxe yet?

NerdOctaxe Rev 3.1

€699.00 In stock

Incl. VAT, plus shipping.

The NerdOctaxe runs the same firmware family as the NerdQAxe++: NerdOS, derived from AxeOS and used the same way, with a dashboard in your browser (it shows the name Nerd*OS), set up through a Wi-Fi network the miner opens itself. What changes is the scale. Eight chips draw around 220 W on both the NerdOctaxe Rev 3.1 and the water-cooled NerdOctaxe Hydro (Rev 3.2), so the power supply, the spot you choose and the fan settings matter more than on a small miner. Everything below describes the firmware these miners ship with, based on version 1.1.2 of the NerdQAxe firmware.

Quick start: plug in the included 12 V power supply, join the open Wi-Fi network Nerdaxe_XXXX shown on the display, enter your 2.4 GHz Wi-Fi, replace the example address in Stratum User with your own Bitcoin address (in the fallback pool as well), save. The pool is preset to pool.bitaxe.de with port 3333.

What you need

NerdOctaxe Rev 3.1NerdOctaxe Hydro (Rev 3.2)
Chips8 × BM13708 × BM1370
Hashrate14 TH/s14 TH/s
Power draw220 W220 W
CoolingAir, two large fansClosed water loop with radiator
Power supply12 V, included12 V / 20 A, included
Network2.4 GHz Wi-Fi2.4 GHz Wi-Fi

Besides the miner you need a 2.4 GHz Wi-Fi network with a normal password, a Bitcoin address from a wallet you control, and a phone or laptop for the setup. Choose the spot before you plug anything in: 220 W around the clock is a noticeable amount of heat in a room.

1. Choose the spot

Put the NerdOctaxe where air can move freely around it, on a shelf or a desk, not in a closed cupboard or a cabinet without ventilation. The fans push air through the heatsinks, and the voltage regulator at the edge of the board needs airflow as well: the firmware reads its temperature separately and shuts the miner down if it overheats. Over months, dust matters too. An owner whose Rev 3.1 kept stopping with an overheated regulator found heavy dust on the board. On the Hydro, the radiator is the part that needs free air.

2. Connect the power supply

The NerdOctaxe takes 12 V through an XT60 connector, the yellow plug at the top edge of the board. Both models come with a 12 V power supply; use that one. Set to about 14 TH/s as we ship them, they draw around 220 W, which is about 18 A at 12 V. If you ever replace the supply, choose 12 V with an XT60 plug and at least 20 A: the firmware warns when the input current passes 25 A (about 300 W) and switches the chips off above 28 A.

Push the XT60 plug in all the way. A connector that gets noticeably warm points to a poor contact or a thin cable, and on a 220 W miner that is worth fixing before anything else. Do not use a supply with a different voltage: the board expects 12 V, and the dashboard flags input voltages outside 11 to 13 V.

NerdOctaxe Rev 3.1 from the front with two large fans, the yellow XT60 power connector at the top left and the display at the top right
The yellow XT60 connector at the top left is the power input; the display sits at the top right.

3. Join the setup network

On the first start the miner cannot reach any Wi-Fi yet, so it opens a network of its own and shows its name on the display: Nerdaxe_ followed by four characters from its hardware address. Join it with your phone or laptop. The setup page usually opens by itself; if it does not, open 192.168.4.1 in the browser.

The setup network has no password, so do the setup in one go. Once the miner has joined your Wi-Fi and received an address, it switches the setup network off for good; until then it opens it again after every restart.

4. Enter Wi-Fi, pool and your Bitcoin address

  • Wi-Fi: pick your network and enter its password. It has to be 2.4 GHz; the ESP32-S3 on the board has no 5 GHz radio.
  • Stratum Host and Port: preset to pool.bitaxe.de and 3333, a solo pool with servers in Frankfurt that charges no fee. Keep them unless you run your own pool.
  • Stratum User: comes filled with an example address. Replace it with your own Bitcoin address. You can add a worker name after a dot, for example bc1q….octaxe.
  • Fallback pool: a second pool is preset for the moments when the first one cannot be reached. Its Stratum User holds the same example address; replace that one as well.
  • Stratum Password: leave it at x.
If the example address stays in place, a block your miner finds would pay that address and not you. Check both pool entries before you save.

The firmware can also split the work between two pools, connect over TLS or use Stratum V2. None of that is needed for a first setup; leave those options as they are.

5. Save, restart and check the first minutes

Save and restart. The miner joins your Wi-Fi; you find its IP address on the display or in the device list of your router. Open that address in a browser on your home network to reach the dashboard. Within a few minutes it should show a hashrate, accepted shares and a best difficulty. Enter your Bitcoin address on pool.bitaxe.de to see the miner from the pool side as well.

Give the hashrate an hour before you judge it: the average over an hour is the figure to compare with the expected hashrate the dashboard shows for your frequency. What best difficulty to expect after a day or a month is in our article Best Difficulty Explained.

The display and its two buttons

The colour display is a small dashboard of its own. One button steps through four screens: mining with hashrate, power and temperatures, the settings with network and pool, the Bitcoin price, and global network statistics. The other button switches the display off and on, which helps at night. Holding both buttons for five seconds shuts the chips down; the display counts down before it happens.

There is no button combination that resets the settings. To start over, change the values on the settings page, or install the firmware again without keeping the settings, as described under firmware updates below.

Frequency, core voltage and expected hashrate

The hashrate of a BM1370 board follows its clock directly. The dashboard calculates the expected hashrate as frequency × 2,040 × 8 chips, which gives these values:

FrequencyExpected hashrateNote
600 MHz9.8 TH/s
650 MHz10.6 TH/s
700 MHz11.4 TH/sFirmware default on Rev 3.1 and later, at 1,210 mV
750 MHz12.2 TH/s
800 MHz13.1 TH/sHighest value in the normal settings list
850 MHz13.9 TH/sLimit of the firmware; our NerdOctaxe ship set close to it

The firmware recognises Rev 3.1 and later boards by their six-phase voltage regulator and offers them 525 to 800 MHz and 1,120 to 1,260 mV in the settings; older four-phase boards stop at 600 MHz. Values outside these lists only appear after you switch on the Danger Zone in the settings, and no board goes above 850 MHz. There is no automatic tuning: every change is made by hand.

We set both models to about 14 TH/s before they ship, close to the upper limit of the firmware, so there is little headroom left upwards. More frequency means more power and more heat, and the efficiency drops the higher you go. If your room runs warm, the regulator temperature climbs or the input current approaches 25 A, lower the frequency in steps of 25 MHz and give each step a few hours. Note the frequency and core voltage before a firmware update: after a reinstall without Keep Settings the miner starts again at the firmware default of 700 MHz, which the dashboard shows as 11.4 TH/s expected.

Cooling, fan control and overheat protection

The fans run under automatic control: the firmware adjusts their speed so that the chip temperature stays around 60 °C. If a temperature reaches the shutdown limit, 70 °C by default, the fans go to full speed, the chips are switched off and the display shows MINER OVERHEATED or VREG OVERHEATED. The miner stays off until you restart it.

On the Rev 3.1 the chip temperature is an estimate: the board measures next to the chips and adds 10 °C, because this revision cannot read the BM1370 itself. The regulator temperature is shown separately, uses the same shutdown limit and has its own protection in the regulator on top. You can change the target temperature and the shutdown limit in the settings, the limit between 50 and 90 °C. Raising it buys hashrate with hotter components and is rarely worth it.

If the temperature climbs although the fans run fast, look for dust on the heatsinks and the regulator, for a heatsink that does not sit flat, or for warm air that cannot escape. One owner traced temperature spikes on a Rev 3.1 to a heatsink that did not sit flat on one chip.

NerdOctaxe Hydro: what is different

The Hydro, Rev 3.2 of the board, uses the same eight chips and the same firmware, but a closed water loop carries the heat to a radiator, where a large fan disposes of it slowly and quietly. Setup, pool and dashboard are exactly as described above.

The firmware has no pump control and no coolant sensor; it only sees the chip and regulator temperatures and the fan speeds. If the temperature on the dashboard rises steadily, check that the pump runs and that the radiator has free air, and keep the radiator away from walls and curtains.

NerdOctaxe Hydro from the front with the tubes of its closed water loop
On the Hydro, tubes carry the heat from the chips to the radiator.

Firmware updates

Updates are installed from the settings page of the dashboard, which lists the available releases and installs one over Wi-Fi. Leave Keep Settings ticked: without it the miner returns to factory defaults, including the example address in Stratum User. Note your pool settings before any update anyway.

If the dashboard does not load after an update, open /recovery on the IP address of the miner. The page lets you upload the file of the web interface again.

Error messages on the display

When the firmware detects a hardware fault, it switches the chips off, shows a message and keeps the miner off until you restart it:

MessageWhat the firmware detectedWhat to check
PSU FAULTNo 12 V at the regulator, or input voltage or current out of rangeSupply plugged in, XT60 fully seated, supply rated at least 20 A
CURRENT PROTECTIONToo much current at the chipsLower frequency or core voltage, then restart
VOLTAGE PROTECTIONCore voltage out of rangeSettings back to the default, then restart
VREG OVERHEATEDVoltage regulator too hotAirflow, dust on the board, room temperature
MINER OVERHEATEDChip temperature above the shutdown limitFans running, heatsinks seated; on the Hydro, pump and radiator
VERIFY FAILEDOnly with the optional payout check: the pool sent work that does not pay your addressStratum Host and Stratum User

After you have fixed the cause, restart the miner from the dashboard or unplug it for a few seconds. If the same hardware message returns right after a restart with default settings, write to us with a photo of the display.

Wired network

Since firmware 1.1.1 the NerdOctaxe can also use a wired connection through a W5500 Ethernet add-on board, which the firmware detects by itself. Wi-Fi remains the normal way; the wired option helps where the signal is weak.

What it costs to run

At about 220 W around the clock, each model uses roughly 1.93 MWh a year. Multiply that by your own tariff before you decide. In winter the heat at least warms the room, as our page on the Bitcoin heater explains.

Products in this guide

Still stuck? The support page collects every setup guide and our contact options; a photo of the display and of the dashboard helps us answer fast. The four-chip models of the same family are covered in the NerdQAxe++ setup guide, and the miner comparison sets every model side by side.

Frequently asked questions

What power supply does the NerdOctaxe need?
Both models come with a 12 V power supply, the one of the Hydro rated 12 V / 20 A. If you ever replace it, use 12 V with an XT60 plug and at least 20 A; at the 14 TH/s setting the miner draws around 220 W, and the firmware warns above 25 A input.
Which pool is preset on the NerdOctaxe?
pool.bitaxe.de with port 3333, a solo pool with servers in Frankfurt that charges no fee, plus a fallback pool. Both come with an example address in Stratum User that you replace with your own Bitcoin address.
What is the name of the setup network?
Nerdaxe_ followed by four characters from the hardware address of the miner; the display shows the exact name. It is an open network and switches off for good once the miner is on your Wi-Fi.
What hashrate does the NerdOctaxe reach?
About 14 TH/s, the Rev 3.1 as well as the Hydro, set up that way before they ship. The dashboard shows the expected value for the frequency that is set; after a reset to the firmware default of 700 MHz it expects 11.4 TH/s, so set the frequency again.
How do I reset the NerdOctaxe?
There is no button combination for a reset. Change the values on the settings page, or install the firmware again from the settings page with Keep Settings unticked, which returns the miner to factory defaults.
Why did my NerdOctaxe stop with VREG OVERHEATED?
The voltage regulator got too hot. Check the airflow and dust on the board, lower the frequency if you raised it, then restart; the miner stays off until you do.
Can the NerdOctaxe use 5 GHz Wi-Fi?
No. The ESP32-S3 on the board supports 2.4 GHz only. Since firmware 1.1.1 a wired connection through a W5500 Ethernet add-on board is possible.
What is the difference between the Rev 3.1 and the Hydro?
Both have eight BM1370 chips and the same firmware, reach about 14 TH/s at around 220 W and come with a 12 V power supply. The Rev 3.1 is air-cooled with two large fans; the Hydro, Rev 3.2 of the board, moves the heat into a closed water loop and a radiator.
How do I switch the screens on the display?
One of the two buttons steps through the mining, settings, Bitcoin price and network statistics screens, the other switches the display off and on. Holding both for five seconds shuts the chips down.

Hear about restocks and new miners first

Restock alerts, new devices and the occasional guide like this one. Sign up and get 5% off your first order.

Your welcome code gives 5% off your first order for 14 days and cannot be combined with the Bitcoin discount.

Next step

Four chips instead of eight

The NerdQAxe++ is the same family with four chips and less heat, small enough for a desk.

All prices in EUR including VAT, plus shipping.